Gutter (75/100/125) Downpipes (63/90) and Accessories
The BRYZA GUTTER SYSTEM is an established product that was brought to market at the beginning of 2004.
BRYZA is a complete system consisting of semi-circular section gutters of 75, 100, and 125 with
a group of fittings and downpipes with two diameters of 63 and 90mm.
The discreet elegance of classic forms, easy installation, and a selection
of two colors in various sizes meet all customer requirements.
Brown (RAL 8017) - Graphite (RAL 7021)
75 System
Gutter 75mm with downpipe 63mm.
For small residential buildings, canopies, garages,
balconies, and attics.
100 System
Gutter 100mm with downpipe 90 or 63mm.
Single-family houses, small and medium-sized storage
buildings, commercial and industrial buildings, and
public buildings.
125 System
Gutter 125mm with downpipe 90mm.
Single and multi-family houses, apartment buildings,
storage buildings, public buildings, commercial
and industrial buildings.
Gutter System Parts
1. "Gutter" 75, 100, 125mm; 2m
2. "Gutter holder" 75, 100, 125mm
3. "Internal corner fitting 90°" 75, 100, 125mm
4. "Gutter connector" 75, 100, 125mm
5. "External corner fitting 90°" 75, 100, 125mm
6. "Connector piece" 75/63, 100/63, 100/90, 125/90mm
7. "Gutter end cap right/left" 75, 100, 125mm
8. "Downpipe" 63, 90mm
9. "T-piece" 63, 90mm
10. "Bracket (PVC)" 63, 90mm
11. "Downpipe connector/socket" 63, 90mm
12. "Reduction" 90/63mm
13. "Bend 67.5°" 63, 90mm
14. "Gutter iron (metal) adjustable" 75, 125mm
15. "Hook for PVC bracket" 120, 160, 180, 220, 250, 350mm
16. "Internal corner piece adjustable angle 120° to 145°" 125mm
17. "External corner piece adjustable angle 120° to 145°" 75, 100, 125mm
Connection Type
The gutters are connected to the pipe fittings by a locking connection.
The connection is sealed with a rubber profile located in the groove of a pipe fitting.
This connection type allows for easy installation and ensures the required
tightness. The connection of the downpipes with the pipe fittings is done with connection
sockets without a gasket. These connection types allow for thermal
length changes of the gutter system parts to be compensated.
Please Note During Installation!
The PVC as well as steel holders are mounted directly to the roof battens or rafters.
The holder distance should be 40-50cm. For proper water drainage, the
gutter should have a slope of 2mm per 1m towards the connector piece.
Cutting the Gutters and Downpipes
Cut the gutter or downpipe to the correct length with a fine-tooth saw at a right angle.
Gutter Installation in the Holders and Installation of Connector Pieces and Parts
Installation in PVC and metal holders begins by inserting the
gutter's front hem into the holder's front nose, then snapping the inner part
of the gutter under the rear nose.
Corner piece, connector piece, and gutter connector are mounted by sliding
them onto the gutter's front hem and then snapping into the rear hem.
When connecting, be sure to check the correct position of the gaskets in the connector pieces,
and corner pieces as well as the stops on the inner surface of these parts.
It is recommended to install additional gutter holders at the gutter connectors, connector pieces, and
corner pieces.
Corner piece, connector piece, and gutter connector are mounted by sliding
them onto the gutter's front hem and then snapping into the rear hem.
When connecting, be sure to check the correct position of the gaskets in the connector pieces,
and corner pieces as well as the stops on the inner surface of these parts.
It is recommended to install additional gutter holders at the gutter connectors, connector pieces, and
corner pieces.
